Why Does My Car Stop Accelerating While Driving?
There can be multiple factors that can cause a car to lose acceleration while driving. Some of the common causes include a low fuel supply, a malfunctioning spark plug, an air filter that is clogged, a broken fuel injector, or a throttle body that is worn out.
Is there a problem with the fuel injectors causing the acceleration to stop?
A potential cause of both symptoms mentioned could be a defective fuel injector, specifically a blockage or clog in the nozzle. When the fuel injector fails to dispense the necessary amount of fuel according to the Electronic Control Unit (ECU), it can result in an imbalanced fuel-air mixture in the combustion chamber. This imbalance can lead to misfiring or a sudden decrease in acceleration.
Read more: Why Does a Car Shake When Driving?
Why is a bad fuel injector important?
It is crucial to diagnose a faulty fuel injector in its early stage to prevent potential engine damage. Poor engine performance, reduced mileage, and increased emissions are common signs of a faulty fuel injector. Neglecting to address this issue promptly can even result in engine failure, as running lean can cause piston damage.
Can a clogged fuel injector cause a detonation?
In turbocharged engines, a fuel injector that is clogged or dirty can potentially have harmful consequences, such as causing a detonation that can lead to engine damage.
When the engine is operating in turbocharged mode at a higher rpm, it demands a significant amount of fuel. If the fuel injector is unable to meet this demand, a detonation may occur, resulting in engine vibrations.
One of the symptoms of a faulty fuel injector is a misfiring engine.
Why does my car stall if a fuel injector fails?
If there is insufficient fuel reaching the combustion chamber, the engine may stall due to the action of the Electronic Control Unit (ECU). Engine stalling as a consequence of a failed fuel injector generally occurs when the nozzle is severely obstructed or when there is a fuel leak at the connection point between the injector and the fuel lines. Symptoms of malfunctioning fuel injectors may include:
Decreased engine performance
Inconsistent idling
Reduced fuel efficiency
Increased emissions
Difficulty starting the engine
If you notice any of these symptoms, it is advisable to have your fuel injectors checked and potentially replaced by a qualified mechanic.
What causes a leaking fuel injector?
One of the primary reasons for leaky injectors is attributed to the O-ring failure at the point where the injector connects with the fuel rail. The extreme heat generated by the engine can cause the O-ring to become rigid and fragile. Consequently, if it ruptures, fuel may escape and potentially result in engine fires.
If you are experiencing issues with your fuel injectors, it is crucial to diagnose and rectify the problem promptly. To assist you in this process, you can refer to The Motor Guy's article on diagnosing and fixing faulty fuel injectors.
Could a faulty throttle position sensor be causing the loss of acceleration?
A faulty throttle position sensor can lead to various symptoms, including slow acceleration, acceleration surges at high and low speeds, hesitation or delay in acceleration, and other related issues.
If the sensor malfunctions, it can result in incorrect adjustments to the air/fuel mixture by the computer, leading to decreased acceleration.
In addition to reduced acceleration, a defective throttle position sensor can also cause difficulties in shifting up, rough or sluggish idle, and a lack of power during acceleration.
Check also Why Does My Car Pull to the Right When Driving?
How do I know if my throttle position sensor is bad?
A failed throttle position sensor can manifest in various symptoms. It is important to note that while some of these symptoms may also be indicative of other engine problems, it is crucial to be aware of the signs of a faulty throttle position sensor. The most frequently encountered symptom is experiencing difficulties with the acceleration of your vehicle.
In addition, you may notice stumbling or hesitation during acceleration, as well as inconsistent or erratic engine performance. These symptoms should not be ignored and prompt attention should be given to diagnose and address the issue with the throttle position sensor.
How does a throttle sensor work?
When you press the gas pedal to increase speed, the computer transmits this data to the sensor. This allows the throttle to determine the appropriate amount of fuel to deliver to the engine. Previously, a cable connected the throttle to the accelerator.
Here are six indications that the throttle position sensor may be malfunctioning, as well as the estimated cost of replacement.
When should a broken throttle sensor be replaced?
To restore full functionality to your vehicle, it is necessary to replace a broken sensor. When your vehicle is experiencing engine issues, identifying the cause can be challenging. Various components, such as the throttle body system, collaborate to ensure the engine's acceleration is seamless. If the throttle position sensor is malfunctioning, there are identifiable symptoms to be aware of.
Is the car experiencing a transmission issue that is affecting acceleration?
When the gas pedal is depressed, the vehicle is intended to increase its speed. However, if this does not happen, it could indicate potential issues such as transmission slippage or a faulty torque converter. Additionally, problems with shift solenoids, a worn clutch, a damaged gearbox, or other drivetrain complications could also be the cause.
Read also Why Did My Car Cut Off While Driving?
What happens if a transmission is faulty?
Internal issues with automatic transmissions, such as problems with the clutch in manual transmissions, can lead to a phenomenon called "slippage." This occurs when the engine RPMs increase, but the vehicle speed does not correspondingly increase. Another potential reason for poor acceleration from a stop is a defective torque converter in an automatic transmission.
"Slippage" is a common term used to describe the situation where the engine RPMs rise without a corresponding increase in vehicle speed. This can occur due to internal problems in automatic transmissions or issues with the clutch in manual transmissions.
If you experience poor acceleration when trying to speed up from a stop, one possible cause could be a faulty torque converter in your automatic transmission. It is essential to address these transmission-related problems promptly to ensure proper vehicle performance.
Why is my automatic transmission slipping?
An automatic transmission that is low on fluid can exhibit similar symptoms of slipping.
If the timing belt or chain has worn out and has jumped a tooth, it can cause issues with power and acceleration.
It is recommended to have a mechanic handle timing belt repairs.
Why is my car straining to accelerate?
There are multiple potential causes for your vehicle's difficulty in accelerating. When you press the gas pedal, various systems, components, and sensors must work together effectively to propel your car forward. If any of these elements fail, it can lead to issues with acceleration. Let's explore what is necessary to deliver the expected power.
Are automatic transmissions mechanically linked to the engine?
Unlike manual transmissions, automatic transmissions are not mechanically linked to the engine. Instead, they are connected through transmission fluid. This means that the speed at which the gears in an automatic transmission spin is determined by the actual speed of the vehicle, not the engine speed.
When it comes to automatic transmissions, there are three factors to consider: gears, acceleration practices, and wear on the transmission. Since the gears are linked to the wheels, the speed of the vehicle affects how fast the gears spin. Proper acceleration techniques and maintenance can help prevent unnecessary wear and tear on the automatic transmission.
Could a clogged air filter be causing a decrease in engine power and acceleration?
A clogged air filter can have a negative impact on acceleration by decreasing power output. The blockages in the filter impede proper air circulation, resulting in inadequate air supply to the engine. As the pores of the filter become clogged, air flow into the engine is restricted, leading to reduced air intake, lower horsepower, and diminished acceleration.
Check also Why Does My Car Only Blow Cold Air When Driving?
Does a clogged air filter drag you down?
A dirty and clogged air filter can impede the airflow in and out of the engine, resulting in decreased performance. As the filter collects more debris and dust, the airflow further diminishes, potentially affecting the engine's power and torque. This can be a concern even for enthusiastic drivers.
In addition, a collapsed air filter can pose dangers to your vehicle's engine. Therefore, it is important to be aware of the potential hazards that a clogged air filter can cause.
How does a dirty air filter affect engine performance?
An engine requires adequate airflow with each revolution to function properly.
A dirty and clogged air filter can impede the flow of air in and out of the engine.
As the air filter accumulates more debris and dust, the airflow decreases, which can potentially affect the engine's power and torque output.
What happens if your engine air filter collapses?
Imagine it like a collapsed lung. In the event of a collapsed air filter, your engine’s air filter will likely detach from the seal or deteriorate. This can have disastrous consequences for the health of your engine. A loose or damaged air filter will allow unfiltered air, containing dust, debris, and other harmful particles, to enter your engine.
A clogged air filter can pose 6 dangers to your vehicle’s engine.
What is an engine air filter & why is it important?
The engine air filter plays a vital role in preventing contaminants, debris, and dirt from entering the engine through the air.
It is important to keep the air filter free of any clogs to ensure the engine receives the proper amount of air for combustion.
As part of routine car maintenance, the air filter should be replaced periodically to prevent clogging that can occur over time.
Is the car entering "limp mode" due to a detected engine or transmission problem?
Limp mode is typically engaged when there are issues with the turbo charge pressure, engine sensors, or transmission in a car. It is important to note some common causes of this mode. These include faulty sensors, overboost situations, knocking or misfires, vacuum or boost leaks, and low fluid levels.
See also Why Does Car Stutter When Braking? How to Deal
Could a malfunctioning mass airflow sensor be responsible for the lack of acceleration?
A bad mass air flow sensor can lead to several driveability issues, such as a no-start condition, stalling, decreased power, and sluggish acceleration.
A faulty MAF sensor can cause an imbalance in the air-fuel mixture, resulting in performance problems in your vehicle.
If the MAF sensor provides inaccurate data to the engine control unit (ECU), it may cause the engine to receive too much air and not enough fuel, leading to poor acceleration.
This is due to a higher ratio of air to fuel, causing a fuel-starved condition in the combustion chamber.
Read more: Why Is My Car Sputtering While Driving?
What happens when a mass air flow sensor goes bad?
Many vehicles utilize a mass air flow (MAF) sensor to accurately measure the quantity of air entering the engine. If this component malfunctions, it can result in a range of symptoms, which may include the activation of the check engine light, as well as issues such as rough running and misfires.
It is important to be aware of the symptoms of a failing mass air flow sensor in order to address any potential problems promptly. By recognizing these indications, such as the illumination of the check engine light or experiencing rough running and misfiring, appropriate action can be taken to rectify the situation and ensure the optimal functioning of the vehicle.
What is the mass air flow sensor on a car?
The mass air flow sensor serves the function of measuring the volume of air that enters the engine. Since the MAF is an important input for the car's computer in determining fuel control, its failure can lead to various noticeable symptoms. Some common issues that can arise from a faulty air flow sensor include:
1. Bogged down engine performance
2. Poor fuel efficiency
3. Rough idling or stalling
2. Hesitation or lack of power during acceleration
5. Check engine light illumination
6. Unusual engine noise
If you are experiencing any of these symptoms, it is advisable to have your mass air flow sensor checked and potentially replaced by a professional.
Can a faulty MAF sensor cause slow acceleration?
A malfunctioning MAF sensor can lead to an inaccurate air-fuel mixture, resulting in various performance problems with your vehicle. One potential issue is reduced acceleration speed. When you observe that your car is notably slower than its usual performance, it is highly likely that the MAF sensor is the culprit.
Additionally, if you are experiencing any of the following symptoms, it could indicate a faulty MAF sensor: (1) rough idling, (2) stalling engine, (3) engine misfires, (4) decreased fuel efficiency, (5) difficulty starting the car, (6) erratic engine behavior, (7) illuminated check engine light, and (8) potential increase in emissions. To resolve the problem, consider a replacement of the MAF sensor. For further details on the signs and the estimated cost of the replacement, you can refer to our article on Mechanic Base.
Is the car experiencing misfires, causing a loss in power and acceleration?
One common scenario in which misfires can occur is when your engine is in high gear, operating at low RPM, and the gas pedal is fully pressed. Misfires can manifest as rough acceleration, which is a typical indication of engine misfiring. Additionally, you may observe other performance problems, such as slower acceleration or engine stalling during acceleration.
Read also Why Does My Car's Heater Only Work When I'm Driving?
What is an engine misfire?
An engine misfire is characterized by the skipping of one or more combustion cycles, resulting in a loss of power, heightened emissions, and potential damage to the engine and exhaust system.
What causes rough acceleration if engine misfire?
Rough acceleration during misfires can often be attributed to several common culprits, including worn-out spark plugs, a cracked distributor cap, a faulty spark plug wire, or a failing throttle position sensor (TPS).
When experiencing an engine misfire, it is likely that the Check Engine Light will illuminate, and in some cases, the vehicle may go into a reduced performance mode known as 'limp mode'.
If you suspect that your engine is misfiring, there are several potential causes that you should consider exploring.
What happens if a car misfires during idling?
Misfires can happen during engine startup or while idling. When a misfire occurs, the engine may momentarily stumble and reduce its RPMs. However, most misfires are temporary and the engine quickly returns to its normal speed after a brief moment.
Can you drive a car with a misfire?
It is not advisable to operate a vehicle with engine misfires due to the potential for significant damage to the internal components of the engine and the catalytic converter. Repairing these damages can be quite expensive. Therefore, it is recommended to promptly diagnose and address any issues related to engine misfires.
An engine misfire is a substantial problem that should be resolved expeditiously. To learn more about the meaning, causes, symptoms, and solutions for engine misfires, refer to the following article: "Engine Misfire - Meaning, Causes, Symptoms & How To Fix It" on MechaniBase.com.
Are the spark plugs worn out, leading to poor engine performance and lack of acceleration?
Defective spark plugs have the potential to harm your engine. They can result in issues like sluggish acceleration, engine misfires, and decreased fuel efficiency. In certain instances, a vehicle with defective spark plugs may fail to start altogether.
Check also Why Is My Car Overheating While Driving?
Why does my car have bad spark plugs?
The poor performance of a vehicle can be attributed to faulty spark plugs that are failing to properly ignite and burn the air-fuel mixture within the engine. This results in a lack of combustion and subsequent loss of power. Typically, poor performance is one of the initial signs indicating that a car may have bad spark plugs.
Another symptom of faulty spark plugs is engine hesitation during acceleration. If the spark plugs are not functioning optimally, they can cause a delay or hesitancy in the engine's response when the accelerator is pressed. It is important to be aware of these and other potential issues that may arise from bad spark plugs.
What causes a jerky engine when accelerating?
In a properly functioning engine, the spark plugs fire in a specific sequence. However, if there is a faulty spark plug, it can cause a delay in the ignition sequence and result in engine surging. Engine surging occurs when there is an excessive amount of air being forced into the engine. This can cause the engine to jerk when accelerating.
Furthermore, a faulty spark plug can also lead to poor fuel economy. It is important to be aware of the symptoms of bad spark plugs, as they can cause various problems in your vehicle. To learn more about these symptoms, you can refer to the article "9 Different Problems to Look Out for!" on carsneedcare.com.
What causes poor acceleration in a car?
One of the most frequent causes of sluggish acceleration in vehicles is a malfunction in the ignition system. In contemporary engines, there are various sensors that communicate with the onboard computer and ignition system, instructing them when to send electrical pulses to ignite the spark plug. Therefore, the problem could potentially lie with a defective sensor.
Could a failing fuel pump be causing a loss of fuel pressure and subsequent acceleration issues?
If a high-pressure fuel pump malfunctions, it can lead to several issues. Firstly, the performance of the vehicle may be compromised, resulting in decreased efficiency. Additionally, the engine may experience sudden stalling or shutdown while in operation, which can be hazardous. Furthermore, the vehicle may lose power and shut down completely, leading to an inability to continue driving. Lastly, the engine may fail to start altogether, as it will not receive the necessary fuel injection to function.
Check also Why Did My Car Die While I Was Driving?
What happens if a fuel pump fails?
If the fuel pump fails to deliver the correct amount of fuel to the engine, it can put excessive strain on the engine, resulting in an abnormal increase in temperature.
Working on your vehicle carries potential hazards and can be messy. To ensure safety and prevent serious injuries or accidents, it is important to have the necessary tools and knowledge before attempting any repairs.
What are the symptoms of a high-pressure fuel pump failure?
A high-pressure fuel pump failure can cause several noticeable symptoms for the driver. One common sign is a decrease in engine performance, which is often observed when the HPFP fails.
If you notice any of these symptoms, it is crucial not to ignore them.
How does a high pressure fuel pump work?
Modern gasoline and diesel engines require high-pressure fuel pumps to deliver fuel to the combustion chambers. These pumps increase fuel pressure to ensure efficient injection and combustion. On a gasoline engine block, the camshaft is responsible for driving the high-pressure fuel pump, which distributes gasoline to fuel injectors at a pressure ranging from 30 to 100 psi.
There are several symptoms of high-pressure fuel pump failure that should not be ignored.
What causes a fuel pump to overheat?
Contaminants have the potential to harm fuel pump components, leading to reduced performance or even complete failure. It is also possible for high-pressure gasoline pumps to become overheated and fail due to excessive workload. In cases where the engine is running hot, there is a risk of the fuel pump overheating due to various factors.
By identifying the symptoms of high pressure fuel pump failure, you can prevent any potential issues from escalating. It is important to pay attention to these symptoms and address them promptly to avoid further damage.
Is the car's electronic throttle control system malfunctioning, affecting acceleration?
Failure of the ETC system can cause unpredictable changes in the speed of the vehicle. When there is an ETC failure, the accelerator may become stuck in an open position, leading to sudden and potentially dangerous acceleration. This acceleration can result in a loss of control over the vehicle.
Read more: Why Does My Car Only Blow Hot Air When Driving?
What happens if a throttle controller is damaged?
Throttle hesitation or problems accelerating can occur when there is a faulty throttle controller in the vehicle. This can cause issues with the engine's acceleration and can lead to a "stumbling" effect when the driver engages the throttle. If these symptoms are present, it is important to have the throttle controller inspected and repaired promptly, as it can impact the performance of the vehicle and pose safety concerns.
How does a throttle control sensor work?
The ECM relies on the throttle control sensor to determine the extent to which the throttle has been opened, enabling it to make precise fuel-to-air ratio adjustments.
If the electronic throttle control light is illuminated, it is important to understand its meaning and learn how to fix the issue. For more detailed information, visit Mechanic B's article on Mechanic Base.
Do electronic throttle control systems wear out over the life of a car?
An electronic throttle control system has fewer moving parts compared to other car components, resulting in less wear and tear over time.
Instead of relying on moving parts, the system uses electric impulses to send signals, further reducing the potential for mechanical failure.
As a result, less maintenance is required for electronic throttle control systems.
What happens if a throttle motor does not detect voltage?
The throttle motor is programmed to shut down the engine if it detects any voltage or signals that were not sent by the engine control module.
In the event of strong electromagnetic interference, the electronic throttle control system is designed to shut down rather than surge forward, ensuring safety.
Learn more about how electronic throttle control systems work on HowStuffWorks.
Is the car experiencing a problem with the throttle body, leading to acceleration issues?
A damaged throttle body can lead to acceleration problems, resulting in insufficient power to move the vehicle forward and potentially causing it to shut down.
In addition, the car may experience spontaneous acceleration even without pressing the gas pedal. This poses a safety risk as it can make it difficult to maintain control of the vehicle while driving.
Can a bad throttle body cause too much fuel?
A malfunctioning throttle body can impede the flow of air to the combustion chamber, resulting in an excessive fuel supply to the engine. Alternatively, it may permit an excessive amount of air to enter the engine, causing fuel deprivation. In either case, noticeable engine issues will arise. Here are the most frequently observed symptoms of a faulty throttle body:
1. Rough idling or stalling
2. Difficulty starting the engine
3. Reduced fuel efficiency
4. Engine misfires or hesitation
5. Acceleration problems or lack of power
6. Throttle response delays
7. Check Engine Light illuminated
8. Unusual noise from the intake system
If you experience any of these symptoms, it may be necessary to replace the throttle body. The cost of replacement will depend on various factors.
How many throttle bodies does a car have?
Generally, the majority of cars are equipped with a single throttle body, although some engines, specifically ones with twin turbochargers, may have two throttle bodies. It is beneficial to familiarize yourself with the symptoms associated with a faulty throttle body as listed above. This knowledge will enable you to make well-informed decisions regarding repairs, ultimately leading to improved longevity and performance of your vehicle.
What happens if a throttle position sensor fails?
If there are issues with the throttle body, it is likely that your car will experience random idle surges. These surges may continue for a period of time before the engine eventually shuts off. In addition to erratic idling, you may also observe a rough idle, misfiring, or engine stalling. These are symptoms of a dirty throttle body. To address this issue, you may need to replace the throttle body at an associated cost.
Should I show my car to a mechanic if my throttle body is dirty?
It is recommended to have your car inspected by a mechanic if you notice any indications of a dirty throttle body. A clogged throttle body can negatively impact the performance of your car and potentially compromise your safety.
Are there any vacuum leaks in the intake manifold causing a loss in engine power?
A vacuum leak resulting from a faulty intake manifold gasket can disrupt the air-fuel mixture of the engine, leading to various performance problems. These issues may include misfires, a decline in power and acceleration, reduced fuel efficiency, and potential instances of stalling.
What causes a vacuum leak?
The two most frequently encountered causes of a vacuum leak are a cracked vacuum hose or a leaking intake manifold gasket. Another potential source of leakage is the throttle body gasket, although this is less common. In rare instances, a cracked intake manifold can also lead to a vacuum leak. It is important to note that locating a vacuum leak, while it may appear straightforward, can at times require a significant investment of time and effort.
What are the symptoms of a bad intake manifold gasket?
A vacuum leak resulting from a defective intake manifold gasket can disrupt the correct balance of air and fuel in the engine, leading to various issues including misfires, decreased power and acceleration, reduced fuel efficiency, and potential stalling.
Coolant leaks are also a common symptom of a faulty intake manifold gasket.
These are some of the signs to look out for that indicate a potential problem with your intake manifold gaskets.
What causes an intake manifold to leak?
Intake manifold leaks are a common issue that can cause trouble for your engine. The gasket used for the intake manifold can be made of various materials such as paper, rubber, or metal, or a combination of these. Its main function is to seal the intake manifold against the cylinder head(s).
These leaks can lead to problems in the engine and should be addressed promptly.
Could a failing oxygen sensor be affecting the car's fuel mixture and causing a lack of acceleration?
A malfunctioning oxygen sensor in a vehicle can lead to several issues. First, it can result in sluggish and rough driving, potentially leading to stalls. Additionally, it can cause poor fuel efficiency, contributing to higher fuel consumption and costs. Furthermore, a faulty oxygen sensor can contribute to increased pollution levels. Moreover, it may result in severe complications with the engine and catalytic converter, which can be quite expensive to repair or replace. Lastly, it can cause a sudden and noticeable decrease in the vehicle's fuel economy.
How does a bad oxygen sensor affect fuel efficiency?
A faulty oxygen sensor can have a noticeable negative effect on your car's fuel efficiency. Inaccurate measurement of the air-fuel mixture by the sensor can result in an engine running rich, meaning there is an excess of fuel in the mixture, causing a decrease in fuel economy.
It is important to be able to recognize the symptoms of a malfunctioning oxygen sensor. To learn more about diagnosing car issues related to oxygen sensors, you can visit auto.howstuffworks.com.
Is it harmful to drive a car with a bad ?
The O2 sensor in a car works by monitoring the oxygen levels in the exhaust.
It reads the exhaust in real time and provides data on the air-fuel ratio to the computer.
Based on this information, the computer adjusts the mixture by controlling the fuel injectors to optimize performance.
As for mixing different brands of fuel, it is generally safe for your vehicle.
However, it is recommended to use the same brand and octane rating consistently for best results.
Using fuel with different qualities may affect the vehicle's overall performance and fuel efficiency.
What happens if a catalytic converter has a bad oxygen sensor?
A defective oxygen sensor can negatively affect the performance of the catalytic converter, which plays a crucial role in converting toxic emissions into less harmful compounds. When the oxygen sensor fails to accurately detect the correct air-fuel ratio, it can result in various issues.
It is important to understand the signs and symptoms of a faulty oxygen sensor in order to identify and resolve the problem efficiently.
Is the car's catalytic converter clogged, resulting in reduced engine power and acceleration?
A clogged catalytic converter can lead to several problems, including sluggish engine performance, reduced speed, and engine shutdown.
Managing pressure buildup becomes more challenging, and there is a risk of overheating due to an excessive amount of unburned gases.
What happens if your catalytic converter is clogged?
A clogged catalytic converter can impede proper airflow in your engine, leading to decreased acceleration and overall performance in your vehicle. Additionally, you may observe a decrease in fuel efficiency. If there is an excessive buildup of exhaust pressure, it can restrict the engine's function and potentially cause it to stall.
How does a catalytic converter work?
A catalytic converter is an essential component that reduces emissions from an engine's exhaust through a chemical reaction.
In terms of structure, the assembly can be divided into two primary sections.
Typically, vehicles are equipped with two converters, with one located near the engine known as the "light-off" cat, which primarily handles NOx emissions. The efficiency of this converter is monitored by a downstream O2 sensor.
If you want to determine if the catalytic converter is clogged, there are several signs you can look out for.
What happens if your catalytic converter fails an emissions test?
When catalytic converters are damaged, they can lead to the failure of your vehicle in an emissions test. Additionally, this can cause damage to other parts of the vehicle, resulting in the need for more costly repairs.
If there are engine issues upstream, it is possible for foreign substances like coolant and oil to enter the exhaust system. This can contribute to further complications with the catalytic converter.
If you suspect that your catalytic converter is clogged, there are a few signs to look out for. To find out more about identifying a clogged catalytic converter, refer to the article "How to Tell If the Catalytic Converter is Clogged" on our blog.
